1. Announcement:
    AUGI HotNews - July 2014
    2014-07-17
    Views:
    388
Page 1 of 74 123451151 ... LastLast
Threads 1 to 20 of 1461

Forum: Inventor - General

Ask your Inventor questions here!

  1. Exclamation Sticky Thread Sticky: AUGI Wish List - Inventor

    Started by mark.kiker, 2010-04-06 03:05 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 3,643
    2013-12-09, 07:22 AM Go to last post
  2. Sticky Thread Sticky: Let us know if a tip helped you!

    Started by jonathan.landeros, 2007-06-21 03:36 PM
    • Replies: 2
    • Views: 3,231
    2013-08-27, 03:02 PM Go to last post
  3. Lightbulb Sticky Thread Sticky: Inventor Tips and Tricks: starting with - Switch between trim and extend

    Started by Buffeldrek, 2006-09-13 08:44 AM
    2 Pages
    1 2
    • Replies: 19
    • Views: 9,769
    2012-12-11, 03:39 AM Go to last post
  4. Thumbs up Sticky Thread Sticky: Solid CAD Files

    Started by Ron Oldenbeuving, 2005-05-05 03:57 AM
    2 Pages
    1 2
    • Replies: 13
    • Views: 8,051
    2009-06-23, 10:39 AM Go to last post
  1. 2015: Inventor 2015 measure angle

    Started by ConMan, 2014-07-18 03:41 PM
    • Replies: 0
    • Views: 21
    2014-07-18, 03:41 PM Go to last post
    • Replies: 0
    • Views: 72
    2014-07-15, 02:43 PM Go to last post
  2. 2015: "make part" or "derive"...which is better?

    Started by mjncad, 2014-07-10 05:41 AM
    • Replies: 4
    • Views: 456
    2014-07-15, 05:19 AM Go to last post
    • Replies: 4
    • Views: 166
    2014-07-15, 12:19 AM Go to last post
  3. 2015: New to piping environment

    Started by frifer, 2014-07-01 06:46 AM
    • Replies: 1
    • Views: 103
    2014-07-10, 06:16 PM Go to last post
  4. 2013: Export to REVIT

    Started by revacservice, 2014-07-01 05:05 AM
    • Replies: 0
    • Views: 78
    2014-07-01, 05:05 AM Go to last post
    • Replies: 2
    • Views: 124
    2014-06-26, 02:56 PM Go to last post
  5. 2015: Positioning Grease Gallery

    Started by Vagulus, 2014-06-22 12:25 AM
    • Replies: 5
    • Views: 152
    2014-06-23, 11:29 PM Go to last post
  6. 2015: Model dimensions not available in drawing

    Started by Vagulus, 2014-06-17 12:47 AM
    • Replies: 7
    • Views: 201
    2014-06-19, 04:33 AM Go to last post
  7. 2013: How to redefine an offset work plane?

    Started by azntwboy, 2014-04-18 03:02 PM
    • Replies: 3
    • Views: 285
    2014-06-18, 02:12 AM Go to last post
  8. 2014: ADAPTIVITY - It Does Not Work - Need Help

    Started by hiandy, 2014-05-02 07:41 AM
    • Replies: 1
    • Views: 242
    2014-06-18, 01:52 AM Go to last post
    • Replies: 0
    • Views: 13
    2014-06-14, 07:26 AM Go to last post
  9. Unhappy 2015: eccentric cone - flattened?

    Started by southpaw49, 2014-05-27 08:56 PM
    • Replies: 2
    • Views: 185
    2014-06-09, 09:11 AM Go to last post
  10. Angry 2015: Zipped tutorial files nightmare - SOS!!!

    Started by southpaw49, 2014-06-02 01:51 PM
    • Replies: 1
    • Views: 93
    2014-06-02, 08:05 PM Go to last post
  11. 2014: Adding an assembly to the Content Center

    Started by robefel662042, 2014-05-19 08:26 PM
    • Replies: 4
    • Views: 273
    2014-05-30, 03:53 PM Go to last post
    • Replies: 0
    • Views: 92
    2014-05-28, 01:06 PM Go to last post
  12. 2014: Crooked views in a drawing or assembly drawing

    Started by jniessen, 2014-05-21 05:35 PM
    • Replies: 1
    • Views: 210
    2014-05-22, 06:20 AM Go to last post
    • Replies: 3
    • Views: 426
    2014-05-21, 07:59 PM Go to last post
  13. Question 2014: Route problem in Tube and Pipe run

    Started by imsbl656512, 2014-05-09 06:25 AM
    • Replies: 0
    • Views: 234
    2014-05-09, 06:25 AM Go to last post
  14. 2013: Center mark always same nb of lines

    Started by clovis, 2014-05-07 07:13 AM
    • Replies: 0
    • Views: 222
    2014-05-07, 07:13 AM Go to last post

Page 1 of 74 123451151 ... LastLast

Forum Information and Options

Moderators of this Forum

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 25 replies or 150 views
Hot thread with unread posts
More than 25 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •