Results 1 to 2 of 2

Thread: TO AVOID ASD2010-REINFORCEMENT-SURFACE REINFORCEMENT DISTRIBUTION-BARS-FATAL ERRORS

  1. #1
    Member
    Join Date
    2015-09
    Posts
    38
    Login to Give a bone
    0

    Default TO AVOID ASD2010-REINFORCEMENT-SURFACE REINFORCEMENT DISTRIBUTION-BARS-FATAL ERRORS

    FOR U-BARS / CREATED BY
    SURFACE REINFORCEMENT DISTRIBUTION-BARS OPTION

    To avoid the fatal errors related to the modification of the ASD2010-REINFORCEMENT-(SURFACE REINFORCEMENT DISTRIBUTION-BARS), the Minimum bar length for surface distribution ( defined in Job preferences / Bars / Options ) should be > = [ (2 x Bar diameter which is shown in the required projection) + Bent diameter (according to the selected code) ].

    This because the Minimum bar length for surface distribution does not mean the total length of the bar, but it means the projection length of the bar.

    If the fatal errors still exist, chamfering the corner with an edge length > = [ (2 x Bar diameter which is shown in the required projection) + Bent diameter (according to the selected code) ] will prevent the errors to come.

    Moreover, the fatal errors are very sensitive to illogical / unreasonable modifications in the following fields (fields of Reinforcement detailing tab in the Reinforcement: definition and detailing dialog box.) :

    1- two edit fields allow determining a value of the distance between the extreme reinforcement and the zone border; there is a possibility to block the distance value for each zone – once the distance on one side is blocked, the distance value on the other side will be automatically adjusted to a specified number of bars and a spacing value; after blocking the distance on both sides, the spacing will be adjusted automatically to a given number of bars.

    2-the button located between the edit fields enables centering the distribution.

    Also, increasing the bar diameter or the cover values without taking care about the above notes, will create the fatal errors.

    I hope that Autodesk to check / review this part of the program, and issue new hotfix or service pack.

    Best of luck.
    Last edited by abbakeer; 2009-10-09 at 02:53 PM.

  2. #2
    Member
    Join Date
    2015-09
    Posts
    38
    Login to Give a bone
    0

    Thumbs up Re: TO AVOID ASD2010-REINFORCEMENT-SURFACE REINFORCEMENT DISTRIBUTION-BARS-FATAL ERRORS

    Finally, Autodesk have issued the best hotfix to solve the fatal errors problem, try it..( ASD 2010_HF5 (32/64-bit) ) in this link.

    http://usa.autodesk.com/adsk/servlet...inkID=12952913

    For old files created before this hotfix, do file recovery first, then modify and update the file as you like.

    Regards,

Similar Threads

  1. Replies: 3
    Last Post: 2011-05-23, 01:08 PM
  2. ASD2010-Reinforcement Module New Fatal Errors after asd_2010_hf5_32bit
    By abbakeer in forum AutoCAD Structural Detailing
    Replies: 0
    Last Post: 2010-01-30, 01:47 PM
  3. ASD2010 / (REINFORCEMENT) / FATAL ERRORS
    By abbakeer in forum AutoCAD Structural Detailing
    Replies: 11
    Last Post: 2009-10-08, 12:24 PM
  4. ASD2010 / REINFORCEMENT FATAL and INTERNAL ERRORS
    By abbakeer in forum AutoCAD Structural Detailing
    Replies: 3
    Last Post: 2009-06-17, 05:37 AM
  5. ASD/ Reinforcement/Surface reinforcement - bars
    By abbakeer in forum AutoCAD Structural Detailing
    Replies: 0
    Last Post: 2008-12-03, 05:44 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •