See the top rated post in this thread. Click here

Page 3 of 5 FirstFirst 12345 LastLast
Results 21 to 30 of 41

Thread: Verification of modal analysis Results

  1. #21
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by mecheil.edward.hanna View Post
    Hi Troy
    Hi Z.G
    Please get the link for this pdf file
    this file show u step by step seismic load by ubc
    But still scale factor without solution by robot
    as I told before we can generate a new combination and multiply the seismic load by the required scale factor
    Hoping it will be useful
    http://www.4shared.com/file/QoEHcxiR/ToTroyAndZG.html

    many thanks edward brother,


    I will first review. I write again later. bye

    ps: you have a big archive in 4shared. its suppper.. thanks.
    can i upload your file from archive? Tower40FloorZiajdenRobot2011.rar


    best regards
    falconado_turkey

  2. #22
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Hi edward,

    You've done a great work. was very surprised. Thank you very much. I now understand more clearly what they want to say.nobody could tell that so well. into the hands of health care.

    about robot model.
    1- my question is floor analiz method is rigid diaphram or only shell?
    2- in our seismic standart have a criteria for peryot. N= number story of building
    peryot not greater than Tx,Ty < 0.1N ( sample number story 40 then T max = 4 second.) this criteria at UBC yet? and why your bulding restraint simple restraint, not fixed. if fixed this base nodes then your period itself will decrease.


    and you are lucky mans. cuz your code and standart exist in Robot and etabs. We are assigning for static lateral load shell is rigid. we are doing rigidity center lateral load. with hands calculate and define value for fx,fy. look we areuse turkish standart but not exist etabs and robot these. :/

    many many thanks

    falconado_turkey
    Last edited by troy_the.best; 2010-08-25 at 09:35 PM.

  3. #23
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by mecheil.edward.hanna View Post
    Hi Troy
    Hi Z.G
    Please get the link for this pdf file
    this file show u step by step seismic load by ubc
    But still scale factor without solution by robot
    as I told before we can generate a new combination and multiply the seismic load by the required scale factor
    Hoping it will be useful
    http://www.4shared.com/file/QoEHcxiR/ToTroyAndZG.html


    dear brother,

    I want to say a few things.

    first ..
    we use scale factor in units ton.meter., but your definition is kip.in. is it mistake?
    second...
    we doing seismic loads analysis, if Vspec > Vstatic never reduce scale factor. because it will be wrong. but seismic (response analysis) are essentially. therefore we cant response spectrum scale factor in etabs and other programs. why do you this reduce? i m not understand, brother. is it right?

    see later

    best regards
    falconado_turkey

  4. #24
    Active Member
    Join Date
    2010-07
    Posts
    67
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by troy_the.best View Post
    dear brother,

    I want to say a few things.

    first ..
    we use scale factor in units ton.meter., but your definition is kip.in. is it mistake?
    second...
    we doing seismic loads analysis, if Vspec > Vstatic never reduce scale factor. because it will be wrong. but seismic (response analysis) are essentially. therefore we cant response spectrum scale factor in etabs and other programs. why do you this reduce? i m not understand, brother. is it right?

    see later

    best regards
    falconado_turkey
    See,
    when you open Etabs by default units will be kpi and you have to change to KN-M
    when we run the model as a first time we put an accelarion of Spectrum diagram 9.81 m/s2
    you can select any value you can put 1 2 or 3 as you want
    We will say this is first scale factor Say FS1 ok
    when we run analysis and we will know the natural period of building then we can get a static shear force
    simply static shear force means the building is rigid i.e the the full energy of seismic will transfere to the building ok

    Last step we have to callibrate the accelarion of seismic for response spec
    this is what we say scale Factor
    so the dinal scale factor of response diagram say SF2= SF1 x Vstatic/Vdyanmic
    ok
    But now you will be confiused and you ask how Vstatic< vdynaimc
    it is not like that just we adjust the accelarion of spectrum curve
    you get my point
    Hoping it is clear

  5. #25
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by mecheil.edward.hanna View Post
    See,
    when you open Etabs by default units will be kpi and you have to change to KN-M
    when we run the model as a first time we put an accelarion of Spectrum diagram 9.81 m/s2
    you can select any value you can put 1 2 or 3 as you want
    We will say this is first scale factor Say FS1 ok
    when we run analysis and we will know the natural period of building then we can get a static shear force
    simply static shear force means the building is rigid i.e the the full energy of seismic will transfere to the building ok

    Last step we have to callibrate the accelarion of seismic for response spec
    this is what we say scale Factor
    so the dinal scale factor of response diagram say SF2= SF1 x Vstatic/Vdyanmic
    ok
    But now you will be confiused and you ask how Vstatic< vdynaimc
    it is not like that just we adjust the accelarion of spectrum curve
    you get my point
    Hoping it is clear

    edward,

    if Vspec > Vstatic ( Vspec too large then Vstatic) then probably a mistake your model or specrtum analysis. values are usually very close. Please pay attention to this point. Have very different results, if the model is broken or not stabil. and dont reduce spec factor (if Vspec is great) absolutely. I know this very well.. please check again this point edward. usually spectrum analysis is essentialy in our solutions. equal lateral static loads for comparison. and have any period restrictions in your Code.


    To use this equation. SF2= SF1 x Vstatic/Vdyanmic (have to be Vstatic>Vspec)

    sorry my english.

    best regards
    falconado_turkey
    Last edited by troy_the.best; 2010-08-26 at 06:27 AM.

  6. #26
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    hi friends,

    i have a question. please look this screenshoot. whats the mean main mode number in seismic case.?

    thanks in advice.


    regards.
    falconado_turkey
    A.S.C.
    Attached Images Attached Images

  7. #27
    Member
    Join Date
    2009-03
    Location
    USSR
    Posts
    38
    Login to Give a bone
    0

    Exclamation Re: Verification of modal analysis Results

    troy_the.best,
    Run modal analysis, then go to Results--Advanced--Modal Analysis. Look at columns name as Cur.mass UX, UY & UZ. Find maximum value in each column and look at number of mode for this value. And now you have main modes for X, Y & Z direction! Just type it in Combination Sign menu (your screenshot).

  8. #28
    Member
    Join Date
    2010-08
    Location
    İstanbul
    Posts
    49
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by romanich View Post
    troy_the.best,
    Run modal analysis, then go to Results--Advanced--Modal Analysis. Look at columns name as Cur.mass UX, UY & UZ. Find maximum value in each column and look at number of mode for this value. And now you have main modes for X, Y & Z direction! Just type it in Combination Sign menu (your screenshot).
    thanks romanich,

    I had already guessed. then what we do? typing mode number and again analysis???? or what? in results will change anything ;??? i can understand this point.
    thanks in advice.

    best regards
    falcoando_turkey
    ASC

  9. #29
    Member
    Join Date
    2009-03
    Location
    USSR
    Posts
    38
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Yes, we run analysis again!

  10. #30
    Active Member
    Join Date
    2010-03
    Posts
    69
    Login to Give a bone
    0

    Default Re: Verification of modal analysis Results

    Quote Originally Posted by troy_the.best View Post
    hi friends,

    i have a question. please look this screenshoot. whats the mean main mode number in seismic case.?

    thanks in advice.


    regards.
    falconado_turkey
    A.S.C.

    Main mode – The number of the main mode for determining the sign of the given combination, so that (as you can see in the attached picture) in the seismic combination on Y direction you will have some braces tensioned and the other ones working in compression.
    Attached Images Attached Images

Page 3 of 5 FirstFirst 12345 LastLast

Similar Threads

  1. Analysis Results as Parameters
    By inventor.wishlist1738 in forum Inventor Wish List
    Replies: 1
    Last Post: 2012-10-06, 02:51 AM
  2. ROBOT Modal analysis results are different from other programs
    By erginc in forum Robot Structural Analysis
    Replies: 2
    Last Post: 2012-07-11, 08:05 AM
  3. Modal/seismic analysis problem:missing eigenvalues
    By dan.suciu488718 in forum Robot Structural Analysis
    Replies: 1
    Last Post: 2012-07-11, 06:39 AM
  4. modal and seismic analysis
    By mecheil2000 in forum Robot Structural Analysis
    Replies: 6
    Last Post: 2011-10-12, 08:58 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •