Results 1 to 4 of 4

Thread: re-orient 3D model to UCS (LOWER LEFT HAND CORNER OF THE SCREEN

  1. 2014-01-23, 09:28 PM #1
    imackenzie515526
    imackenzie515526 is offline
    Member
    Join Date
    2014-01
    Posts
    2
    Login to Give a bone
    0

    Default re-orient 3D model to UCS (LOWER LEFT HAND CORNER OF THE SCREEN

    Hello All,
    I have made a 3d assembly, made a idw , then went back and made improvements to the model, then went back to the idw. then I discovered the views are all disoriented?
    I then went back to the 3D assembly model and relized the model is not oriented to the ICS in the lower left hand corner of he screen.
    please advise how to correct, since I still consider myself a rookie when it comes to Inventor..

    Many thanks for your expertise!
    Reply With Quote Reply With Quote
  2. 2014-01-24, 06:02 PM #2
    Paul Munford
    Paul Munford is offline
    100 Club
    Join Date
    2006-08
    Location
    London
    Posts
    177
    Login to Give a bone
    0

    Default Re: re-orient 3D model to UCS (LOWER LEFT HAND CORNER OF THE SCREEN

    Did you make sure that at least one part was grounded? This will prevent unintentional movement.
    Reply With Quote Reply With Quote
  3. 2014-01-29, 02:03 AM #3
    JD Mather
    JD Mather is offline
    All AUGI, all the time
    Join Date
    2000-12
    Location
    Williamsport, PA
    Posts
    641
    Login to Give a bone
    0

    Default Re: re-orient 3D model to UCS (LOWER LEFT HAND CORNER OF THE SCREEN

    Assuming you failed to ground the first part.
    Create Mate-Flush constraints between the assembly origin planes and the first part origin planes.
    Reply With Quote Reply With Quote
  4. 2014-05-21, 07:59 PM #4
    jniessen
    jniessen is offline
    Active Member
    Join Date
    2005-02
    Location
    Richmond BC
    Posts
    67
    Login to Give a bone
    0

    Default Re: re-orient 3D model to UCS (LOWER LEFT HAND CORNER OF THE SCREEN

    Just figured this one out on another thread.


    http://forums.augi.com/showthread.ph...sembly-drawing
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. Lower Left and Upper Right Corner
    By avinash patil in forum VBA/COM Interop
    Replies: 1
    Last Post: 2011-08-31, 11:10 AM
  2. 2008: page setup not 0,0 in lower left corner
    By jledgewood in forum AutoCAD General
    Replies: 7
    Last Post: 2011-07-19, 01:57 PM
  3. ACA 2009 UCS returns to lower left corner after panning
    By dzatto in forum ACA General
    Replies: 7
    Last Post: 2008-04-18, 02:17 PM
  4. Find the lower left corner of polyline rectangle
    By avinash00002002 in forum AutoLISP
    Replies: 5
    Last Post: 2007-04-28, 08:52 AM
  5. Get the top most left corner & bottom right corner point of a closed Polyline
    By KHADREE_SHARIFF in forum AutoLISP
    Replies: 4
    Last Post: 2007-04-08, 12:45 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules