See the top rated post in this thread. Click here

Results 1 to 3 of 3

Thread: XYZ axis askew when UCS World

  1. #1
    Woo! Hoo! my 1st post
    Join Date
    2018-03
    Posts
    1
    Login to Give a bone
    0

    Default XYZ axis askew when UCS World

    Working for weeks on acad 2018 mechanical dwg that has 2d and 3. On Friday, XYZ coordinate, while in modelspace (not in a viewport) went askew, with z coordinate slightly off normal axis. My nav cube also askew. I set UCS to world, the view zooms out and rights itself, showing all objects. But when I zoom in next, I often get blank screen: it zooms too far and I have extreme difficulty zooming/scrolling and I notice that nav cube is askew and so is my model. Also, perspective of 3 d objects is different than I've seen in 3d: displays as if parallel lines have vanishing points. Did I fat finger some setting? It's almost too hard too work in modelspace. UCS world and XYZ axis is fine when going to MS via viewports.

  2. #2
    100 Club duhvinci's Avatar
    Join Date
    2007-08
    Location
    Rockford, Illinois
    Posts
    156
    Login to Give a bone
    1

    Default Re: XYZ axis askew when UCS World

    It sounds as though you are in perspective view mode. Move your cursor up to the upper left hand corner of the window and change to parallel. Maybe an inadvertent mouse click up in that area changed.
    Patrick Hughes -

    CadTempo - Time Tracking for AutoCAD, AutoCAD LT, Revit, Inventor...
    http://www.cadtempo.com

  3. #3
    Woo! Hoo! my 1st post
    Join Date
    2012-02
    Posts
    1
    Login to Give a bone
    1

    Default Re: XYZ axis askew when UCS World

    Hello,

    I have run into the same problem - the world isn't the world anymore. Your absolutely correct it just a little bit off and we shouldn't have to perform work arounds in today's AutoCAD. I tried the 3D view command - front view, right side view etc., which worked for me. Another solution was to draw a 2D line and perform a ucs - za align, to properly align the viewport. But it's only temporary to the working viewport when you change it to another view you lose it. It's frustrating when such a small , maybe half a degree makes a lot of difference when your modeling.

    Let me know if you find out anything different.

Similar Threads

  1. 2016: Revit Tags - Leader Lines are Askew
    By dcalloway in forum Revit MEP - Families
    Replies: 0
    Last Post: 2016-06-09, 02:57 PM
  2. 'Section box' in {3D} view can be rotated about X or Y axis as well as Z axis.
    By Wish List System in forum Revit Architecture - Wish List
    Replies: 0
    Last Post: 2012-02-06, 07:34 AM
  3. 2011: lock in one axis
    By ivan.239950 in forum AutoCAD General
    Replies: 3
    Last Post: 2010-06-16, 02:34 PM
  4. Lines on X axis are drawn at varying Z axis
    By s.nail in forum AutoCAD 3D (2006 or below)
    Replies: 16
    Last Post: 2006-09-20, 04:23 AM
  5. Joining slighltly askew conc. beams
    By paullee in forum Revit Structure - General
    Replies: 1
    Last Post: 2006-08-29, 01:47 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •