See the top rated post in this thread. Click here

Results 1 to 6 of 6

Thread: Bing Map clipped?

  1. #1
    Certified AUGI Addict cadtag's Avatar
    Join Date
    2000-12
    Location
    Cairo - no, not Illinois
    Posts
    5,069
    Login to Give a bone
    0

    Default Bing Map clipped?

    I don't do a lot of work in Georgia, but this job is in Ft Benning. Using C3d 2017, and setting the zone to GA State Plane West Ft. When I load the bing map, I'm only getting SW Georgia, all of South Alabama, and Florida Panhandle. the image cuts off about 120 Mi North of the GA-FL state line, about 12-15 miles south of my area of interest.

    Thee are only two zone in GA, East and West, and they roughly bisect the state. WTF does Geomaps cut off?

  2. #2
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default Re: Bing Map clipped?

    Attached is what I got when I tried it.
    and it changed slightly depending on my zoom level.

    FT. BENNING 1.JPG

  3. #3
    Certified AUGI Addict cadtag's Avatar
    Join Date
    2000-12
    Location
    Cairo - no, not Illinois
    Posts
    5,069
    Login to Give a bone
    1

    Default Re: Bing Map clipped?

    I did find a resolution of sorts... the dwt I started with had a North FL zone already set, and changing the zone in C3D had zero effect on Geomaps. I ended up creating a new dwt with _no_ zone established, started a new dwg from that, and then set the GA West zone.

    What I did not try, that might have worked in the original DWG, would have been to remove the geolocation information, zone, etc, save and close, then re-open the drawing and set the GA West after opening.

  4. #4
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default Re: Bing Map clipped?

    did you get the full map? as you can see i only got a portion of it. i did start with a dwt that was in Louisiana South zone and changed it to GA west Ft.

  5. #5
    Certified AUGI Addict cadtag's Avatar
    Join Date
    2000-12
    Location
    Cairo - no, not Illinois
    Posts
    5,069
    Login to Give a bone
    1

    Default Re: Bing Map clipped?

    yes, once I started with a dwt that had no zone I could bring in the aerial and roads for all of GA West.

  6. #6
    Administrator Opie's Avatar
    Join Date
    2002-01
    Location
    jUSt Here (a lot)
    Posts
    9,096
    Login to Give a bone
    0

    Default Re: Bing Map clipped?

    Quote Originally Posted by rmk View Post
    did you get the full map? as you can see i only got a portion of it. i did start with a dwt that was in Louisiana South zone and changed it to GA west Ft.
    That is a long way from GA.
    If you have a technical question, please find the appropriate forum and ask it there.
    You will get a quicker response from your fellow AUGI members than if you sent it to me via a PM or email.
    jUSt

Similar Threads

  1. 2017: bing map
    By rmk in forum AutoCAD Civil 3D - General
    Replies: 4
    Last Post: 2018-09-19, 04:16 PM
  2. 2016: bing map issue
    By rmk in forum AutoCAD Civil 3D - General
    Replies: 1
    Last Post: 2017-11-16, 06:23 PM
  3. 2016: Bing image
    By rmk in forum AutoCAD Civil 3D - General
    Replies: 5
    Last Post: 2017-06-13, 09:03 PM
  4. 2016: bing map issue
    By rmk in forum AutoCAD Civil 3D - General
    Replies: 2
    Last Post: 2017-01-09, 01:32 AM
  5. Binding a clipped Xref and erase the clipped out part
    By mbickerton in forum AutoCAD General
    Replies: 4
    Last Post: 2007-05-11, 06:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •