See the top rated post in this thread. Click here

Results 1 to 7 of 7

Thread: Quick select is not permitted in perspective view?

  1. #1
    I could stop if I wanted to
    Join Date
    2003-11
    Posts
    440


    Default Quick select is not permitted in perspective view?

    When I initiate the qselect command I receive the error in the title. I tried to dview, selected all objects, then typed off, still same error. What else can I do?

  2. #2
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,598


    Default Re: Quick select is not permitted in perspective view?

    Hi

    Check out the following Technical Documents on the Autodesk web site under the Knowledge Base section -

    ID: TS21997 - Switching between parallel projection and perspective view mode

    ID: TS17740 - Cannot draw objects or zoom after exiting 3DORBIT command in perspective view

    Have a good one, Mike

  3. #3
    I could stop if I wanted to
    Join Date
    2003-11
    Posts
    440


    Default Re: Quick select is not permitted in perspective view?

    Those didn't help.

  4. #4
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,598


    Default Re: Quick select is not permitted in perspective view?

    Hi

    From what you've described it sounds like you need to turn OFF Perspective View.

    If you are doing that and still experiencing the issue/problem can I please suggest that you post the drawing file here (I assume Rightly or Wrongly this issue/problem is occurring within *only* one drawing file) so we can take a look.

    Have a good one, Mike

  5. #5
    I could stop if I wanted to
    Join Date
    2003-11
    Posts
    440


    Default Re: Quick select is not permitted in perspective view?

    here is the dwg it 2000i format.
    again, the prblem is when I want to go into qselect.

    thanks.
    Attached Files Attached Files

  6. #6
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,598


    2 members found this post helpful.

    Default Re: Quick select is not permitted in perspective view?

    Hi

    Please find attached "QS_Problem_Fix.dwg", you should now be able to use ._QSelect within this drawing file.

    Below is what I done to correct the drawing file -

    Command: ._Dview
    Select objects or <use DVIEWBLOCK>: _All
    2027 found
    1 was not in current space.
    Select objects or <use DVIEWBLOCK>:
    Enter option
    [CAmera/TArget/Distance/POints/PAn/Zoom/TWist/CLip/Hide/Off/Undo]: _PO
    Specify target point <1303549.211, 429745.035, 1.048E+99>: 0,0,0
    Specify camera point <1303549.211, 429745.035, 1.048E+99>: 0,0,1
    Enter option
    [CAmera/TArget/Distance/POints/PAn/Zoom/TWist/CLip/Hide/Off/Undo]:
    Regenerating model.

    ************

    Check out the following Technical Document on the Autodesk web site under the Knowledge Base section -

    ID: TS59340 - Plot or preview shows incorrect area of drawing when plotting limits

    Have a good one, Mike
    Attached Files Attached Files

  7. #7
    I could stop if I wanted to
    Join Date
    2003-11
    Posts
    440


    Default Re: Quick select is not permitted in perspective view?

    That fixed it.

    thanks mike

Similar Threads

  1. 2014: USING QUICK SELECT
    By rmk in forum AutoCAD General
    Replies: 3
    Last Post: 2014-02-21, 06:17 PM
  2. Replies: 5
    Last Post: 2011-12-28, 05:30 PM
  3. Properties > Quick Select
    By CADKitty in forum AutoCAD Tips & Tricks
    Replies: 10
    Last Post: 2009-04-17, 04:53 PM
  4. Quick Select
    By jrichardson in forum Revit Structure - Wish List
    Replies: 1
    Last Post: 2005-10-06, 10:38 AM
  5. Quick Select - Now that ain't right!
    By CADMama in forum ACA General
    Replies: 8
    Last Post: 2004-09-06, 10:45 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •