Results 1 to 6 of 6

Thread: Looking for stamp

  1. #1
    I could stop if I wanted to
    Join Date
    2006-06
    Location
    Olympia, Washington, U.S.A.
    Posts
    359
    Login to Give a bone
    0

    Default Looking for stamp

    Hey all,

    I'm looking for an Idaho architect stamp in drawing (prefered) or 1:1 image. I went to the Id. state site and I haven't been able to find the dimensions for it. if you know where the symbol is located on the web i would appreciate the address as well.

    Thanks in advance,
    ~Frank

    Addendum #1
    Idaho has been found
    California, Arizona, Oregon and Alaska Stamps are now needed.
    Last edited by Gigliano70; 2009-02-12 at 07:22 PM. Reason: addendum#1

  2. #2
    Certified AUGI Addict jaberwok's Avatar
    Join Date
    2000-12
    Location
    0,0,0 The Origin
    Posts
    8,570
    Login to Give a bone
    0

    Default Re: Looking for stamp

    There are a couple of threads in here about "state seals". I don't know whether Idaho is mentioned though.
    Try the forum search.

  3. #3
    I could stop if I wanted to
    Join Date
    2006-06
    Location
    Olympia, Washington, U.S.A.
    Posts
    359
    Login to Give a bone
    0

    Default Re: Looking for stamp

    Quote Originally Posted by jaberwok View Post
    There are a couple of threads in here about "state seals". I don't know whether Idaho is mentioned though.
    Try the forum search.
    thanks but, did that. Most are engineers stamps. Idaho isn't among the arch stamps.

  4. #4
    Member
    Join Date
    2002-04
    Location
    Gresham, Oregon
    Posts
    28
    Login to Give a bone
    0

    Default Re: Looking for stamp

    I know it's a pain, but several years ago when we started needing Oregon and Washington stamps, we had to draw them from scratch and get them approved. If no one has done this in Idaho yet you may have to go this route. I used to work for the Idaho State Dept. of Parks and Rec. as a board drafter (about 100 years ago - there were three of us then). You might try calling there (in Boise) and see if they have one yet. They may be easier to reach and talk to than the Highway dept. but you could try them also. Good Luck!

  5. #5
    I could stop if I wanted to
    Join Date
    2006-06
    Location
    Olympia, Washington, U.S.A.
    Posts
    359
    Login to Give a bone
    0

    Default Re: Looking for stamp

    I found the idaho stamp and was informed that I now have to do the same for California Arizona Oregon and Alaska as well.

    what i've done is made a dynamic block of all the architects Washington state stamps. we have architects here that are also licensed and we do work in the states listed above. the DB lookups are getting really confusing. but it's fun.

  6. #6
    I could stop if I wanted to
    Join Date
    2006-06
    Location
    Olympia, Washington, U.S.A.
    Posts
    359
    Login to Give a bone
    0

    Default Re: Looking for stamp

    Quote Originally Posted by IamSnave View Post
    I know it's a pain, but several years ago when we started needing Oregon and Washington stamps, we had to draw them from scratch and get them approved. If no one has done this in Idaho yet you may have to go this route. I used to work for the Idaho State Dept. of Parks and Rec. as a board drafter (about 100 years ago - there were three of us then). You might try calling there (in Boise) and see if they have one yet. They may be easier to reach and talk to than the Highway dept. but you could try them also. Good Luck!
    would you be willing to share the oregon stamp. If yes, please take your architects personal information off before you send.
    Thanks!
    ~Frank

Similar Threads

  1. PDF Stamp
    By schizar272632 in forum AutoCAD Fields
    Replies: 1
    Last Post: 2013-07-16, 05:59 AM
  2. Add PE stamp to PDF
    By framedNlv in forum AutoCAD Plotting
    Replies: 8
    Last Post: 2012-05-30, 08:20 PM
  3. Stamp Toggle
    By tcupp in forum Revit Architecture - General
    Replies: 6
    Last Post: 2010-08-10, 06:57 PM
  4. date stamp
    By mgonzales.224492 in forum AutoLISP
    Replies: 7
    Last Post: 2010-01-22, 09:58 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •