Tablet template

[vincent.81973]

I'm using ACAD 2000, and do not use a drawing tablet. Yet the tablet template from ACAD 12 was useful as a reminder of commands.

I have misplaced the tablet templates that came with ACAD 12 and ACAD 2000. All I need is the lower half of the template, which contains the template's permanent commands.

Could someone scan and email a copy of a template?

Regards, Vin

[CADMama]

I'm using ACAD 2000, and do not use a drawing tablet. Yet the tablet template from ACAD 12 was useful as a reminder of commands.

I have misplaced the tablet templates that came with ACAD 12 and ACAD 2000. All I need is the lower half of the template, which contains the template's permanent commands.

Could someone scan and email a copy of a template?

Regards, Vin
Good luck with your quest.
I am replying to answer you question that you sent via email about posting.
CADMama

[CADMama]

I'm using ACAD 2000, and do not use a drawing tablet. Yet the tablet template from ACAD 12 was useful as a reminder of commands.

I have misplaced the tablet templates that came with ACAD 12 and ACAD 2000. All I need is the lower half of the template, which contains the template's permanent commands.

Could someone scan and email a copy of a template?

Regards, Vin
Did you do a search on your harddrive for Template.dwg?
I have the 2005 version of it but not sure you could open it.
Donnia

[Glenn Pope]

Did you do a search on your harddrive for Template.dwg?
I have the 2005 version of it but not sure you could open it.
Donnia
You can save it down to a lower version and post it.

[CADMama]

You can save it down to a lower version and post it.
DOH - I knew there was a reason to keep you around.

Vin - here you go - attaching it now.
CADMama

[vincent.81973]

Did you do a search on your harddrive for Template.dwg?
I have the 2005 version of it but not sure you could open it.
Donnia

Search produced KECA1-template.dwg. It is the template ready to be filled in, but otherwise contains nothing.

[vincent.81973]

DOH - I knew there was a reason to keep you around.

Vin - here you go - attaching it now.
CADMama

Donnia, many thanks. I downloaded your attachment.

Vin

[vincent.81973]

DOH - I knew there was a reason to keep you around.

Vin - here you go - attaching it now.
CADMama

Many thanks. You prompted me to look in my ACAD2000 files. I came across 8 KB TABLET.DWG (dated 1993) -- which doesn't look much like my accustomed ACAD12 template. But then, your 918 KB TABLET-2000.DWG looks (from memory) identical to ACAD12's -- but with a 6X9 section added to the uppermost left corner, impinging somewhat on the User's custom section.

Surprising that my AC2000 tablet DWG seems foreign; yet your AC2005 tablet DWG seems consistent with the old AC12 -- with slight augmentation. Hmm. Not surprising with your 918 KB file, it has much better resolution.

Anyhow, I have what I need. Many thanks.

Regards, Vin

[vincent.81973]

DOH - I knew there was a reason to keep you around.

Vin - here you go - attaching it now.
CADMama

I should post this as a new thread -- but cannot figure out how to do that.

The new thread is:

Attachment AugiEdit.jpg shows my attempt to edit. The original "s" is correct, but I see no way to assert that, or to continue with the edit process.

Regards, Vin

[vincent.81973]

I should post this as a new thread -- but cannot figure out how to do that.

The new thread is:

Attachment AugiEdit.jpg shows my attempt to edit. The original "s" is correct, but I see no way to assert that, or to continue with the edit process.

Regards, Vin

Preview Post does not show whether AugiEdit was attached -- but evidently it was. Attached AugiPreview.jpg shows Preview (*again w/o verifying attachment -- and shows that Preview provides no option to edit. Only option is to Submit Reply. There must be some way to edit Preview before sending -- otherwise Preview is idle.

Regards, Vin

[Mike.Perry]

Hi Vin

In "Preview" mode, the "Reply to Thread" area should still be visible underneath the "Preview" area (refer to attached image), therefore you should be able to simply scroll down to the "Reply to Thread" area and edit your message before posting (Submitting).

Thanks, Mike

Forum Moderator