Herringbone Hatch Pattern

[sam woodward]

Hi All;

i have been trying for many evenings now without much luck to do do a 100mm x 600mm herringbone hatch pattern with 2mm joints. i will be gratefull is anyone can put me on the right track.
Many thanks,
Sam

[hugh.69031]

From HatchKit's Brick&Tile wizard, try:


;-------------------------------------------------------------------------------
; Written by HatchKit for AutoCAD
; HatchKit for AutoCAD (c)1990-2017 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-03-09
;-Time : 08:46:47
;-HatchKit Version : 3.1.10.2717
;-HatchKit Output Filetype : AutoCAD format
;-------------------------------------------------------------------------------
*herringbone,LEFT-HAND 600mmx100mm weave=1/1
89.9904808475,0,0,1213.99832184,10.2016944929,100,-11938.0001661
0.0095191525147,0,100,1213.99832184,-10.2016944929,600,-11438.0001661
-90.0095191525,600,100,1213.99832184,10.2016944929,100,-11938.0001661
180.009519153,600,0,1213.99832184,-10.2016944929,600,-11438.0001661
89.9904808475,-102,-500,1213.99832184,10.2016944929,600,-11438.0001661
0.0095191525147,-102,100,1213.99832184,-10.2016944929,100,-11938.0001661
-90.0095191525,-2,100,1213.99832184,10.2016944929,600,-11438.0001661
180.009519153,-2,-500,1213.99832184,-10.2016944929,100,-11938.0001661


hth,

Hugh Adamson
www.hatchkit.com.au

[sam woodward]

Thank you Hugh, that's brilliant, works a treat.

regards
Sam

[elmourabtarchi939519]

*buttedhb,Butted Herringbone parquetry
0, 0,0, .1,.1, .6,-.4
90, .5,-.6, -.1,.1, .6,-.4

[sam woodward]

Hi Hugh,

I hope you don't mind me asking, any chance you could do a 100x500mm Chevron hatch pattern(trapezoidal 45 degree angle pieces) again with 2mm joints?
best regards,
Sam

[hugh.69031]

Hi Hugh,

I hope you don't mind me asking, any chance you could do a 100x500mm Chevron hatch pattern(trapezoidal 45 degree angle pieces) again with 2mm joints?
best regards,
Sam

sure:

;-------------------------------------------------------------------------------
; Written by HatchKit for Revit
; HatchKit for Revit (c)1990-2017 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-03-14
;-Time : 10:36:10
;-HatchKit Version : 3.1.10.2733
;-HatchKit Output Filetype : Revit with HatchKit Add-In
;-------------------------------------------------------------------------------
;%VERSION=3.0
;%UNITS=MM
*Brick1,LEFT-HAND 500mmx100mm weave=1/1
;%TYPE=MODEL
135.028547969,0,0,1011.99588833,-8.50423412125,500,-11542.0014948
44.9714520305,1.4142,-142.84,1011.99588833,8.50423412125,500,-11542.0014948
135.028547969,-70.711,-70.711,1011.99588833,-8.50423412125,500,-11542.0014948
44.9714520305,-69.296,-72.125,1011.99588833,8.50423412125,500,-11542.0014948
135.028547969,354.97,210.72,1011.99588833,-8.50423412125,100,-11942.0014948
44.9714520305,-70.711,-70.711,1011.99588833,8.50423412125,100,-11942.0014948
135.028547969,1.4142,-142.84,1011.99588833,-8.50423412125,100,-11942.0014948
44.9714520305,-424.26,282.84,1011.99588833,8.50423412125,100,-11942.0014948


- required a rotation before saving that pattern.

hth,
Hugh

[sam woodward]

Morning Hugh

thank you for doing this, each tile is still a rectangle with 90 Degrees, what i needed was a 500x100 tile that is trapezoidal with internal angles 45,and 135 so that they form a chevron pattern when they are butted together.

many thanks,
Sam

[hugh.69031]

Morning Hugh

thank you for doing this, each tile is still a rectangle with 90 Degrees, what i needed was a 500x100 tile that is trapezoidal with internal angles 45,and 135 so that they form a chevron pattern when they are butted together.

many thanks,
Sam

My mistake, misread. While I'm 90% sure of your intent, this gets away from the HatchKit Brick and Tile Wizard into pattern editing so could you please provide a sketch.

thanks,
Hugh

[dgorsman]

I'd be cautious about trying to use hatches for representation of physically dimensioned objects like tiles, blocks, or bricks. Like line types they're symbolic in purpose so there's no guarantee of proper sizes and positions.

You might consider using an array of dynamic blocks for this.

[sam woodward]

HI hUGH
I did a sketch but didn't know how to attach the pdf file, i have attached a photograph of the tile pattern that i am trying to achieve, I hope it helps.
best regards,
Sam
106237

[sam woodward]

Hi dgorsman;

Thank you for your reply, so how do I set about creating this pattern using dynamic block?
regards,
Sam

[hugh.69031]

HI hUGH
I did a sketch but didn't know how to attach the pdf file, i have attached a photograph of the tile pattern that i am trying to achieve, I hope it helps.
best regards,
Sam


Based on the available information showing parallelograms rather than trapeziums:

;-------------------------------------------------------------------------------
; Written by HatchKit for AutoCAD
; HatchKit for AutoCAD (c)1990-2017 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-03-15
;-Time : 14:20:39
;-HatchKit Version : 3.1.10.2717
;-HatchKit Output Filetype : AutoCAD format
;-------------------------------------------------------------------------------
*chevrons,DXF Entity Section
44.9934960888,0,141.42,1012.8276065,7.28654125654,500,-13577.5980704
44.9934960888,0,0,1012.8276065,7.28654125654,500,-13577.5980704
-44.9934960888,-355.55,494.97,1012.8276065,-7.28654125654,500,-13577.5980704
-44.9934960888,-355.55,353.55,1012.8276065,-7.28654125654,500,-13577.5980704
-90,-355.55,494.97,0,711.106782906,141.42,-2.82978301277
-90,0,141.42,0,711.106782906,141.42,-2.82978301277
-90,-2,141.42,0,711.106782906,141.42,-2.82978301277
-90,353.55,494.97,0,711.106782906,141.42,-2.82978301277

Be assured that hatch patterns are accurate, and can be placed accurately in a drawing.

hope this helps,

Hugh

[sam woodward]

Hi Hugh,

Many thanks for your help, I don't know what I would have done without it, you certainly deserve a drink!

kindest regards,

Sam

[se7en745050]

Hello, could I trouble someone to help me create a herringbone pattern with 200x300 pavers similar to the attached image please, I'm so stuck with the pattern definition....
106819

[hugh.69031]

Try this:

;-------------------------------------------------------------------------------
; Written by HatchKit for AutoCAD
; HatchKit for AutoCAD (c)1990-2018 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-09-27
;-Time : 10:32:32
;-HatchKit Version : 3.1.11.2769
;-HatchKit Output Filetype : AutoCAD format
;-------------------------------------------------------------------------------
*Herringbone300x200,LEFT-HAND 300mmx200mm weave=1/1
0,0,0,700,-100,500,-700
90,300,0,700,100,500,-700

hth,
Hugh Adamson
www.hatchkit.com.au

[khaleelwassu773429]

Dear,

Can you provide coding for tile size 260x65 with 2mm grout herringbone with 45 angle.

- - - Updated - - -

Dear,

Need coding for Herringbone 260x65 with 2mm Grout, 45 degree angle.

[hugh.69031]

Dear,

Can you provide coding for tile size 260x65 with 2mm grout herringbone with 45 angle.





try this:

;-------------------------------------------------------------------------------
; Written by HatchKit 4 Standard Edition
; HatchKit 4 Standard Edition (c)1990-2020 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2021-07-05
;-Time : 17:33:28
;-HatchKit 4 Version : 4.0.9.2894
;-HatchKit 4 Output Filetype : AutoCAD
;-------------------------------------------------------------------------------
*Hrringbone260x65+2,
45,90.51,-185.26,-529.998950897,6.09196589822,65,-5698.00008676
45,0,0,-529.998950897,6.09196589822,260,-5503.00008676
45,-93.338,-1.4142,-529.998950897,6.09196589822,65,-5698.00008676
45,-45.962,45.962,-529.998950897,6.09196589822,260,-5503.00008676
135,183.85,183.85,529.998950897,6.09196589822,65,-5698.00008676
135,136.47,-139.3,529.998950897,6.09196589822,260,-5503.00008676
135,0,0,529.998950897,6.09196589822,65,-5698.00008676
135,90.51,-185.26,529.998950897,6.09196589822,260,-5503.00008676





hth,
Hugh Adamson
www.hatchkit.com.au