Horizontal wall split?

[raeburnmark]

I am anew user trying to create a 2X6 wall with gyp. bd. interior, plywood sheathing, and succo exterior finish with 3'-0" of 4" thick stone at the bottom of the wall. I have searched the help and tutorials but to no avail. The problem is that after splitting the exterior finishes at 3'-0" I can't modify the layers to show only stone below and only stucco above. I'm sure this is a simple solution and would greatly appreciate any help. Also, how does one set up the layers to show batt insulation in the same space as the framing?

[aaronrumple]

Much like this....

[Mike.Perry]

I am anew user trying to create a 2X6 wall with gyp. bd. interior, plywood sheathing, and succo exterior finish with 3'-0" of 4" thick stone at the bottom of the wall. I have searched the help and tutorials but to no avail. The problem is that after splitting the exterior finishes at 3'-0" I can't modify the layers to show only stone below and only stucco above. I'm sure this is a simple solution and would greatly appreciate any help. Also, how does one set up the layers to show batt insulation in the same space as the framing? Hi

Welcome to the AUGI Forums :)

I think your question/query would be better answered in one of the appropriate software Forums ie

Revit General (http://%3Cfont%20size=%222%22%3Ehttp://forums.augi.com/forumdisplay.php?f=6)

ADT General (http://%3Cfont%20size=%222%22%3Ehttp://forums.augi.com/forumdisplay.php?f=41)

Which Autodesk product are you using?

Would you like me to *move* this Topic (Thread) to a more appropriate Forum?

Below snippet is taken from the small print found on the Forum General (http://forums.augi.com/forumdisplay.php?f=44) page ( Click HERE (http://forums.augi.com/attachment.php?attachmentid=28398) to see a screen capture )...

<snip>
New users: Please experiment here with forum features and commands.
</snip>

Thanks, Mike

Forum Moderator

[raeburnmark]

Hi

Welcome to the AUGI Forums :)

I think your question/query would be better answered in one of the appropriate software Forums ie

http://forums.augi.com/forumdisplay.php?f=6]Revit General (

http://forums.augi.com/forumdisplay.php?f=41]ADT General (Below snippet is from the small print on the Forum General (http://forums.augi.com/forumdisplay.php?f=44) page (also refer to attached image) -

<snip>
New users: Please experiment here with forum features and commands.
</snip>

Thanks, Mike

Forum Moderator

Thank you! I am using Revit 6.1. I thought I had posted to Revit General! please feel free to move this thread to whichever forum you deem most appropriate.

All the best,

Mark

[raeburnmark]

Much like this....
Hi Aaron,

Yes, very similar to this. How did you achieve this?

Thanks,

Mark

[aaronrumple]

The brick (stone) is a sweep. The air space is a split region in the wall editor.

[raeburnmark]

Hello again,

Sorry to bother you again - this is my first project on revit.

Is it necessary to split the eifs layer at the relevant hight or does the sweep just remove the eifs where the sweep is? Also how does one show batt insulation in the wall section? Is it shown in the wall properties or is it added in 2D later?

Thank you much,

Mark

[Mike.Perry]

Hi Mark

Done.

Please note I've *moved* this Topic (Thread) from the New Users Forum (http://forums.augi.com/forumdisplay.php?f=47) to this one as discussed between Mark and myself.

Thanks, Mike

Forum Moderator