Results 1 to 3 of 3

Thread: Meshing issues

  1. #1
    Login to Give a bone
    0

    Default Meshing issues

    Hi, I'm a new Robot user, and have been given a rather complex Revit model to analyse in Robot. The export from Revit to Robot was not without issue, although the warnings in Robot have now mostly been resolved.

    I have now attempted to mesh the model, which was a long way from being successful. I attempted to mesh the entire model in one go, is this the best option?
    In some areas the model did not mesh at all, in others nodes were created but no mesh linked them up.
    To attempt to resolve this I deleted the isolated nodes, and ran local mesh generation on the unmeshed panels, is this the right thing to do? Once this was done unsurprisingly there were many areas of incoherent meshing at junctions of core walls and slabs. Can anyone advise on the best way to resolve this issue? I attempted to move some of the nodes manually to link them up but this just caused further issues.

    Advice on the above would be very welcome.

    Thanks

  2. #2
    Active Member
    Join Date
    2012-02
    Posts
    97
    Login to Give a bone
    0

    Default Re: Meshing issues

    Hi

    If you have model with many panels in it, meshing whole structure in one go rarely works. Usually best way but unfortunately quite slow way is to mehs first all wall panels floor by floor and then all slabs. This gives usually good mesh.

    One thing is that in Robot two points are connected to eah other or they aren't. There's no such thing as "close enough." So if somebody else has modelled your structure in Revit, there might be some minor mistakes in Revit model that gives you a lot of headache in Robot. That's why if I have to do a Robot model using panels I avoid importing anything as reference or directly in Robot since references or imports may contain minor geometry mistakes that will cause you a lot's of headache in form of incoherent mesh. I've found that for me it seems to be easiest and fastest way to model whole structure in Robot or use use very simple dwg references where all geometry is 100 % right and simplified enough for analysis.

    Hope this helps a little.

  3. #3
    Member
    Join Date
    2010-04
    Posts
    46
    Login to Give a bone
    0

    Default Re: Meshing issues

    The effects you observe suggest that inaccuracies still exist in your model.
    As written by jpo82 the sequenatial meshing of first walls and then slabs may help a little.

    Additionally you can change meshing parameters from controlled by the number of division to controlled by the base size of the mesh and you can switch off regular mesh. It is discribed also in message 4 of this forum post: http://forums.autodesk.com/t5/Autode...ght/true#M2401
    Some improvement can be often obtained increasing the tolerance of model generation - specifying user-defined value on Structure Model tab of Analysis Type window.
    If model is somehow regular then defining grid lines and using Edit/Detailed Correct to snap to them may correct the model and help to avoid meshing problems.
    Useful API tools for inspection and correction of Robot models can be found in other posts of above mentioned forum.

    Regards,
    Pawel Pulak
    Support Specialist
    Autodesk, Inc.

Similar Threads

  1. AU201-1L: Meshing Around With AutoCAD
    By Autodesk University in forum AutoCAD
    Replies: 0
    Last Post: 2014-11-17, 05:28 AM
  2. meshing problems
    By strozy in forum Robot Structural Analysis
    Replies: 8
    Last Post: 2010-07-07, 02:03 PM
  3. Surfacing with Nurbs Meshing
    By inventor.wishlist1738 in forum Inventor Wish List
    Replies: 0
    Last Post: 2007-09-04, 03:54 AM
  4. Meshing Routine? Joining 3dface elements?
    By n3xutl in forum AutoLISP
    Replies: 1
    Last Post: 2005-02-17, 06:18 PM
  5. 3D Meshing and Solids
    By n.murray in forum AutoCAD 3D (2006 or below)
    Replies: 5
    Last Post: 2004-07-07, 10:56 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •