Herringbone Hatch Pattern

[sam woodward]

Hi All;

i have been trying for many evenings now without much luck to do do a 100mm x 600mm herringbone hatch pattern with 2mm joints. i will be gratefull is anyone can put me on the right track.
Many thanks,
Sam

[hugh.69031]

From HatchKit's Brick&Tile wizard, try:


;-------------------------------------------------------------------------------
; Written by HatchKit for AutoCAD
; HatchKit for AutoCAD (c)1990-2017 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-03-09
;-Time : 08:46:47
;-HatchKit Version : 3.1.10.2717
;-HatchKit Output Filetype : AutoCAD format
;-------------------------------------------------------------------------------
*herringbone,LEFT-HAND 600mmx100mm weave=1/1
89.9904808475,0,0,1213.99832184,10.2016944929,100,-11938.0001661
0.0095191525147,0,100,1213.99832184,-10.2016944929,600,-11438.0001661
-90.0095191525,600,100,1213.99832184,10.2016944929,100,-11938.0001661
180.009519153,600,0,1213.99832184,-10.2016944929,600,-11438.0001661
89.9904808475,-102,-500,1213.99832184,10.2016944929,600,-11438.0001661
0.0095191525147,-102,100,1213.99832184,-10.2016944929,100,-11938.0001661
-90.0095191525,-2,100,1213.99832184,10.2016944929,600,-11438.0001661
180.009519153,-2,-500,1213.99832184,-10.2016944929,100,-11938.0001661


hth,

Hugh Adamson
www.hatchkit.com.au

[sam woodward]

Thank you Hugh, that's brilliant, works a treat.

regards
Sam

[sam woodward]

Hi Hugh,

I hope you don't mind me asking, any chance you could do a 100x500mm Chevron hatch pattern(trapezoidal 45 degree angle pieces) again with 2mm joints?
best regards,
Sam

[hugh.69031]

Hi Hugh,

I hope you don't mind me asking, any chance you could do a 100x500mm Chevron hatch pattern(trapezoidal 45 degree angle pieces) again with 2mm joints?
best regards,
Sam

sure:

;-------------------------------------------------------------------------------
; Written by HatchKit for Revit
; HatchKit for Revit (c)1990-2017 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-03-14
;-Time : 10:36:10
;-HatchKit Version : 3.1.10.2733
;-HatchKit Output Filetype : Revit with HatchKit Add-In
;-------------------------------------------------------------------------------
;%VERSION=3.0
;%UNITS=MM
*Brick1,LEFT-HAND 500mmx100mm weave=1/1
;%TYPE=MODEL
135.028547969,0,0,1011.99588833,-8.50423412125,500,-11542.0014948
44.9714520305,1.4142,-142.84,1011.99588833,8.50423412125,500,-11542.0014948
135.028547969,-70.711,-70.711,1011.99588833,-8.50423412125,500,-11542.0014948
44.9714520305,-69.296,-72.125,1011.99588833,8.50423412125,500,-11542.0014948
135.028547969,354.97,210.72,1011.99588833,-8.50423412125,100,-11942.0014948
44.9714520305,-70.711,-70.711,1011.99588833,8.50423412125,100,-11942.0014948
135.028547969,1.4142,-142.84,1011.99588833,-8.50423412125,100,-11942.0014948
44.9714520305,-424.26,282.84,1011.99588833,8.50423412125,100,-11942.0014948


- required a rotation before saving that pattern.

hth,
Hugh

[sam woodward]

Morning Hugh

thank you for doing this, each tile is still a rectangle with 90 Degrees, what i needed was a 500x100 tile that is trapezoidal with internal angles 45,and 135 so that they form a chevron pattern when they are butted together.

many thanks,
Sam

[elmourabtarchi939519]

*buttedhb,Butted Herringbone parquetry
0, 0,0, .1,.1, .6,-.4
90, .5,-.6, -.1,.1, .6,-.4

[se7en745050]

Hello, could I trouble someone to help me create a herringbone pattern with 200x300 pavers similar to the attached image please, I'm so stuck with the pattern definition....
2018-09-26_2013.png

[hugh.69031]

Try this:

;-------------------------------------------------------------------------------
; Written by HatchKit for AutoCAD
; HatchKit for AutoCAD (c)1990-2018 Cadro Pty Ltd
; www.hatchkit.com.au/
;-------------------------------------------------------------------------------
;-Date : 2018-09-27
;-Time : 10:32:32
;-HatchKit Version : 3.1.11.2769
;-HatchKit Output Filetype : AutoCAD format
;-------------------------------------------------------------------------------
*Herringbone300x200,LEFT-HAND 300mmx200mm weave=1/1
0,0,0,700,-100,500,-700
90,300,0,700,100,500,-700

hth,
Hugh Adamson
www.hatchkit.com.au