Results 1 to 7 of 7

Thread: corridor surface

  1. #1
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default corridor surface

    I can't figure out how to fix this. see image

    my corridor looked fine, but the surface is not working out so good.

    any ideas on how to fix this?

    thanks
    Attached Images Attached Images

  2. #2
    Administrator Opie's Avatar
    Join Date
    2002-01
    Location
    jUSt Here (a lot)
    Posts
    9,096
    Login to Give a bone
    0

    Default Re: corridor surface

    Do you have the breaklines option checked when creating the surface from the corridor?

    Or can you show what your assembly looks like?
    If you have a technical question, please find the appropriate forum and ask it there.
    You will get a quicker response from your fellow AUGI members than if you sent it to me via a PM or email.
    jUSt

  3. #3
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default Re: corridor surface

    I first built a corridor with just the lanes for the entire length of the alignment.
    then I built a corridor surface for that.
    then I created the medians in two halves, pulled profiles from the corridor surface.
    then I built a new corridor with the attached assembly. the corridor looks great.
    but when I create the corridor surface with top links (breakline option checked) I get want you see in the below image.

    I also tried adding top curb and flowline breaklines as well but that didn't help.

    thanks
    Attached Images Attached Images

  4. #4
    Administrator Opie's Avatar
    Join Date
    2002-01
    Location
    jUSt Here (a lot)
    Posts
    9,096
    Login to Give a bone
    0

    Default Re: corridor surface

    Let me make sure I understand you.

    You have two corridors and associated surfaces. The first corridor is the lanes without the island. You have a surface associated with that. The second corridor and surface is the island based off of profiles from the surface of the first corridor.

    How does the second corridor surface appear? Does it look as expected alone?

    I'm not seeing where you have any surface attached to your curb assemblies from the back of curb to the center of the island.

    Are you pasting the two surfaces into another surface?
    If you have a technical question, please find the appropriate forum and ask it there.
    You will get a quicker response from your fellow AUGI members than if you sent it to me via a PM or email.
    jUSt

  5. #5
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default Re: corridor surface

    I created the first surface for the sole purposed of pulling profiles for the island alignments. Once that was done I froze that surface and corridor.
    then i created my second corridor using the 2 subassemblies from below. the surface shown below if from this second corridor.
    I haven't connected the 2 curb assemblies yet. do you think the is the issue?
    no pasting is involved, both are independent of each other.

  6. #6
    Administrator Opie's Avatar
    Join Date
    2002-01
    Location
    jUSt Here (a lot)
    Posts
    9,096
    Login to Give a bone
    0

    Default Re: corridor surface

    Can you post a sample drawing? We could go back and forth with questions and answers that may be found in a drawing.

    Otherwise, is this one or two alignments for the curb assemblies? It appears to be two alignments based on the appearance of the assemblies.
    If you have a technical question, please find the appropriate forum and ask it there.
    You will get a quicker response from your fellow AUGI members than if you sent it to me via a PM or email.
    jUSt

  7. #7
    All AUGI, all the time
    Join Date
    2004-06
    Location
    Slidell, Louisiana
    Posts
    968
    Login to Give a bone
    0

    Default Re: corridor surface

    the drawing is over 3 megs. not sure if that can be uploaded

Similar Threads

  1. 2014: Problem pasting a corridor Surface on another surface
    By JBeernaerts in forum AutoCAD Civil 3D - Surfaces
    Replies: 2
    Last Post: 2021-04-07, 10:26 PM
  2. Corridor LandXML to include the true corridor & associated objects
    By Wish List System in forum Civil 3D Wish List
    Replies: 2
    Last Post: 2015-11-16, 11:00 AM
  3. I create a Corridor Surface but no Corridor Surface appears?
    By eraska in forum AutoCAD Civil 3D - Corridors
    Replies: 3
    Last Post: 2007-08-21, 09:50 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •