See the top rated post in this thread. Click here

Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Copy & Paste problem - Pasted objects are offset?

  1. #1
    Member
    Join Date
    2004-07
    Posts
    2
    Login to Give a bone
    0

    Default Copy & Paste problem - Pasted objects are offset?

    AutoCAD 2006

    when using cntrl c then cntrl v, the pasted object is offset badly. Same for all objects-blocks, lines etc. Only in one drawing though....--copy with base point works fine. Any ideas?

  2. #2
    I could stop if I wanted to mom of 3's Avatar
    Join Date
    2004-07
    Location
    jUSt in the middle
    Posts
    366
    Login to Give a bone
    1

    Default Re: Copy & Paste problem - Pasted objects are offset?

    my guess is the drawings are different coordinates. I always use base point when I do copy-paste. that's my thoughts.........

  3. #3
    All AUGI, all the time Richard McDonald's Avatar
    Join Date
    2002-01
    Location
    At right angles to reality
    Posts
    537
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    When using ctrl c and then ctrl v my understanding is that ACAD give the items a arbitrary insertion point.

    If you need items in a certain place use ctrl+shift+c to copy with base point or if your drawings share the same co-ordinate system you can use the Edit>>Paste to original co-ordinates command.

    Hope this helps
    Last edited by Statler; 2007-02-14 at 04:51 PM. Reason: I got the shortcut wrong

  4. #4
    Member
    Join Date
    2004-07
    Posts
    2
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    does anyone know how to change the "arbitrary insertion point" that AutoCAD assigns to copied objects? What is it based on? Thanks!

  5. #5
    I could stop if I wanted to mom of 3's Avatar
    Join Date
    2004-07
    Location
    jUSt in the middle
    Posts
    366
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    I don't think you can. like Richard said (better than I did), it's probably because the drawings are different coordinates. if you copy by base point (0,0), then paste to that same point, your items should fall in the correct place that you want them to.

  6. #6
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,657
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    Hi

    Maybe look at the _.Base command.

    Have a good one, Mike

  7. #7
    All AUGI, all the time Richard McDonald's Avatar
    Join Date
    2002-01
    Location
    At right angles to reality
    Posts
    537
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    What will help is if I give the right info.

    Its ctrl+shift+c to copy with a base point

  8. #8
    AUGI Director scott.wilcox's Avatar
    Join Date
    2015-11
    Location
    Edmonton, Alberta
    Posts
    990
    Login to Give a bone
    0

    Default Re: Copy & Paste problem - Pasted objects are offset?

    Quote Originally Posted by jrisk
    does anyone know how to change the "arbitrary insertion point" that AutoCAD assigns to copied objects? What is it based on? Thanks!
    I think the arbitrary point is somewhere near the lower left corner of the selected geometry.

    I have redefined crtl+shift+V to paste to original coordinates, and assigned crtl+shift+B to paste as block. ctrl+C then ctrl+shift+V does it.

  9. #9
    Certifiable AUGI Addict tedg's Avatar
    Join Date
    2005-06
    Location
    in the upper right corner
    Posts
    3,524
    Login to Give a bone
    1

    Thumbs up Re: Copy & Paste problem - Pasted objects are offset?

    Quote Originally Posted by scott.wilcox
    I think the arbitrary point is somewhere near the lower left corner of the selected geometry.

    I have redefined crtl+shift+V to paste to original coordinates, and assigned crtl+shift+B to paste as block. ctrl+C then ctrl+shift+V does it.
    I use "copy with basepoint" and "paste to original coordinates" all the time. I've created aliases for 'copybase' and 'pasteorg' in my pgp file [see below].

    CB, *COPYBASE

    PO, *PASTEORIG

    I usually use these like:

    "cb" (you pick a basepoint) then "ctr+v" (you pick the insertion point).
    or
    "ctrl+c" (you simply select you objects) then "po" paste to original coordinates.
    It's very important that your ucs is in the same coordinate in both locations or it won't work.

    I always have my "uscicon" "on" just to be sure.

    good luck

  10. #10
    Woo! Hoo! my 1st post
    Join Date
    2002-01
    Posts
    1
    Login to Give a bone
    1

    Default Re: Copy & Paste problem - Pasted objects are offset?

    Had the same issue and it was a USC issue. Did a 3d view top and now works fine...

Page 1 of 2 12 LastLast

Similar Threads

  1. 2012: Auto CAD Copy/Paste Problem
    By eldosrajan401784 in forum AutoCAD General
    Replies: 5
    Last Post: 2013-03-08, 04:07 PM
  2. Copy/Paste Objects to All Layout Tabs
    By autocad.wishlist1734 in forum AutoCAD Wish List
    Replies: 1
    Last Post: 2011-11-23, 02:00 AM
  3. copy and paste problem on sheets
    By iankids in forum Revit Architecture - General
    Replies: 4
    Last Post: 2008-10-22, 06:43 AM
  4. AutoCAD 2002 unable to Copy and Paste Objects
    By chrisr in forum AutoCAD General
    Replies: 2
    Last Post: 2006-08-29, 11:19 PM
  5. Copy and Paste Objects move from location, how do I retain control
    By robert.1.hall72202 in forum AutoCAD General
    Replies: 25
    Last Post: 2006-02-21, 06:26 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •