Results 1 to 10 of 10

Thread: MVPart connection problem

  1. #1
    Member
    Join Date
    2007-09
    Posts
    36
    Login to Give a bone
    0

    Default MVPart connection problem

    Ok, so i created a slot diffuser for a job and when i place it in the drawing my duct connection is not correct. I had set it to be in the middle of the diffuser and it keeps going to the end for some reason. Any ideas on what I did wrong or why this is happening - I've attached a drawing showing it.
    Attached Files Attached Files

  2. #2
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Can you upload the .xml file for it too? That is where the connection location will be defined.

    -Buzz

  3. #3
    Member
    Join Date
    2007-09
    Posts
    36
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Yeah, here you go.
    Thanks
    Attached Files Attached Files

  4. #4
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Hey Kevin,

    Did you try following these steps: http://www.geniusoftllc.com/mvparts/create.asp

    -Buzz

  5. #5
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Hey Kevin,

    Sorry I didn't realize that your original uploaded .dwg was not the actual mvpart .dwg - you will need to upload that one too.

    There are 3 files for an mvpart: SDS-10.xml, SDS-10.dwg, and SDS-10.bmp

    -Buzz

  6. #6
    Member
    Join Date
    2007-09
    Posts
    36
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Buzz,
    Here you go, the other two files I should have uploaded this morning.

    Thanks for your help.

    Kevin
    Attached Images Attached Images
    Attached Files Attached Files

  7. #7
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Found it. The insertion point for the block named "SDS-10 Top" is different than all the other ones.

    -Buzz

  8. #8
    Member
    Join Date
    2007-09
    Posts
    36
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    cool, thanks buzz - i figured it was something stupid like that - i just couldn't find it.

  9. #9
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    Here is the fixed version of your .dwg - simply replace your current one with this one and then regen your catalog (Command: AECBCatalogRegen)

    -Buzz
    Attached Files Attached Files

  10. #10
    All AUGI, all the time
    Join Date
    2007-10
    Location
    Tucson, Arizona
    Posts
    613
    Login to Give a bone
    0

    Default Re: MVPart connection problem

    No sweat Kevin, have fun!

    -Buzz

Similar Threads

  1. 2010 FDO Connection Problem In AutoCad
    By hemantcarpenter364021 in forum AutoCAD Map 3D - Data Connect (FDO)
    Replies: 0
    Last Post: 2013-03-08, 09:46 AM
  2. Welded Connection Problem
    By mfoster.247831 in forum AutoCAD Structural Detailing
    Replies: 6
    Last Post: 2010-04-15, 03:56 AM
  3. steel connection problem
    By MariusRizea in forum Revit Structure - Families
    Replies: 5
    Last Post: 2010-03-23, 06:52 AM
  4. Moment connection problem
    By RafeRedmond in forum Revit Architecture - General
    Replies: 1
    Last Post: 2008-04-22, 10:32 PM
  5. A Mvpart problem
    By claire1027 in forum AMEP General
    Replies: 3
    Last Post: 2007-06-21, 09:55 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •