Results 1 to 7 of 7

Thread: image not plotted

  1. #1
    Member
    Join Date
    2004-08
    Posts
    16
    Login to Give a bone
    0

    Unhappy image not plotted

    this goes in the line of image not display, however I am running Autocad 2004 and I see the block (a sink) put when I go to plot it does not show. I have checked the layer to see if it is frozen...nothing. I have checked to see it the plotter was set to not plot that layer....nothing. I have no clue.

  2. #2
    AUGI Addict
    Join Date
    2015-12
    Location
    Arizona
    Posts
    2,478
    Login to Give a bone
    0

    Default Re: image not plotted

    I'm confused??
    Is it a block (sink)
    or is it an image of the sink?

    Please post it here for us to review.

  3. #3
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,656
    Login to Give a bone
    0

    Default Re: image not plotted

    Hi

    Please note I've *moved* this thread from the AutoCAD Customization Forum to this one as I feel this particular Forum is a more appropriate place for such a topic.

    Thanks, Mike

    Forum Moderator

  4. #4
    The Silent Type Mike.Perry's Avatar
    Join Date
    2000-11
    Posts
    13,656
    Login to Give a bone
    0

    Default Re: image not plotted

    Hi

    Check out the following Technical Document on the Autodesk web site under the Knowledge Base section -

    ID: TS67479 - Raster images do not plot

    Have a good one, Mike

  5. #5
    Active Member richardtt33978's Avatar
    Join Date
    2002-06
    Location
    Somerset, NJ
    Posts
    86
    Login to Give a bone
    0

    Wink Re: image not plotted

    Here's another similar post.

    http://forums.augi.com/showthread.php?p=47429#post47429

    HTH
    R.
    ... SMILE ... the work will always be there, but you don't have to be there .... try again tomorrow.

  6. #6
    Member
    Join Date
    2006-08
    Location
    Melbourne, Australia
    Posts
    6
    Login to Give a bone
    0

    Default Re: image not plotted

    This link is no longer valid.

  7. #7
    Administrator Opie's Avatar
    Join Date
    2002-01
    Location
    jUSt Here (a lot)
    Posts
    9,096
    Login to Give a bone
    0

    Default Re: image not plotted

    Does this one help?
    If you have a technical question, please find the appropriate forum and ask it there.
    You will get a quicker response from your fellow AUGI members than if you sent it to me via a PM or email.
    jUSt

Similar Threads

  1. 2015: Insert image, unload image, image border stays around
    By invaderkyle in forum AutoCAD General
    Replies: 4
    Last Post: 2015-04-10, 03:23 PM
  2. Raster Image rotates when plotted.
    By mdrabic.186488 in forum AutoCAD Map 3D - General
    Replies: 0
    Last Post: 2008-10-21, 04:21 PM
  3. Image (attached as OLE's) are rotating when Plotted via AutoCAD 2005
    By sudhirkizhakoote in forum AutoCAD Plotting
    Replies: 3
    Last Post: 2007-03-09, 06:53 AM
  4. Image resolution looks poor on Plotted output
    By crabe in forum AutoCAD Plotting
    Replies: 3
    Last Post: 2006-03-16, 08:08 AM
  5. Plotted OK before, but not now
    By russell.harris in forum AutoCAD Plotting
    Replies: 1
    Last Post: 2004-07-30, 07:27 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •